1970 Corvette Street Machine

-
Image
                 Street Freak Special ! This 1970 Corvette has such an outrageous custom paint job that it will blind you. The car is a time capsule bringing you back to 1975 when disco was popular, it also was a time when horsepower wasn't enough to win at shows so the people mixed street machine power with lowrider good looks. The Vette features a full custom interior, supercharged small block engine and a 4-speed manual transmission. The interior is filled with a roll bar, metallic vinyl interior accents and wood trim, finishing off the 70's vibe it rolls on classic wire wheels.     The engine is a small-block Chevy 400, with a Dyers 6V-71supercharger. It has a pump gas friendly 8.5:1 CR., The supercharger is feed by two boost-referenced Holley 650 CFM  carbs. Ignition is handled by a MSD products.  The small-block is backed up by a Muncie 4-speed manual transmission. The fumes exit in style with chrome 4-into one side pipes that make this 71' Corvette rumble. Power
Post a Comment

Nitro Nancy Matter

-

 

        Nancy Matter Nostalgia Funny Car Pilot 
 
 Nancy's prior career was in the music industry , she started her own studio and now has about 70 gold and platinum records (that she worked on), and some Grammy's and Oscars.   

She ran an Alcohol Funny Car for 14 years, then in 2017 she switched to a 1977 Pontiac Trans AM Nostalgia Funny Car . 

I'm honored to share her story with you !

Stay tuned for her full story , it will be posted on her own page.    

Also check out a preview of her story in my post about women in Drag Racing .


Full story here !

https://shoptourhardcoredragracing.blogspot.com/p/nancy-matter-funny-car-pilot.html

 
 

Comments

Post a Comment

Popular posts from this blog

What's in the Garage *Paul Kaufmann's 76 Arrow*

-
Image
  In this installment of What's in The Garage  we check out Paul Kaufmann's over the top Plymouth Arrow. What was once an old street race car from Detroit, it's now a Hemi powered street-machine that looks like noting else on the road.           This one is still in the garage but its about to break free. Ten years were spent on this build spanning over four states; New Jersey, Connecticut, Georgia and now Florida.    The story is extensive and Paul has many people to thank. Paul stated that this his first EFI project and its been a blast getting together. Lots of engineering went into planning and executing the build, he had two machinists, one body guy, one chassis shop, and an engine & transmission builder, the list goes on & on !     Paul states he is still wrapping up technical issues and getting ready for the road.   Paul stated that the street tires and wheelie bars don't jive but he had the chassis shop build them for him so he can get her on the
Click here to read this article»

Scott Robinson's "Bionic Wasp" 68' Camaro

-
Image
  Scott Robinson is from southern California and has been into cars his whole life, his earliest memories recount his time spent with his father and his friends. Scott's father raced all types of vehicles, drag boats, sand rails, and cars. These experiences made a major impression on Scott and he couldn't wait to be old enough to drive. When he was old enough, he got heavy into off-road motorcycles then when he got his driver's license all bets were off.  Scott forgot about racing motorcycles and went all in and started racing cars. The first car he raced wasn't car at all, it was a 1975 Chevy van. But this wasn't  any old worn out work van. This van belonged to Scott's father, it featured  a destroked 400 cube small-block built by Scott's Dad, it's backed up with a TH-400 automatic transmission and a narrowed 12-bolt rear end. Scott said it was fun ride for his first car, and when he graduated high-school his father gave it to him.   The father and son
Click here to read this article»

Improve your cars ET with this week's Tip !

-
Image
   This week's tip will improve your muscle cars performance ! Cold fuel will vaporize more quickly than hot fuel, so adding a cooler can add horsepower. You can buy one or you can save some cash by making one. Take a large coffee can and line a coil of copper tubing around inside of it. Drill holes at the top and bottom of the can for the copper line to enter and exit.  Attach the appropriate fittings to the copper line to connect it in series to the Carb. Seal the line to the can to prevent leaks. Connect the fuel lines, fill the can with water, and inspect the can for leaks. If there are no leaks, fill the can to the top with ice, and install the lid. As fuel circulates through the copper coil, the ice will cool it.  When it hits the hot manifold, it will vaporize instantly, and be ready to ignite when the plug fires!  You can drop 1-2-tenths off a 1/4-mile time,and increase speed by 4-5 mph. Moroso also makes a plastic version that keeps the ice colder and it doesn't rust o
Click here to read this article»